AeroPod, PowerPod and Newton

I am now thinking that the V5 did calibrate. But does go into a loop. I checked in the software and could see that the ppV5 was calibrated. I did a very short ride. Wind seems normal and the power values do as well. Please check this ride file Velocomp_2024_05_08_1738_0_km.ibr If this is good. I wil...

I am using best. So after a couple of hours. V3: O&B ride worked and Power values looked OK. Again no CalRide file on device. Fireware 9.02 V5: After the first CalRide. The power values didn't look right. So I went for a ride the values were completely wrong. 4 watt going up a slope. And 300 on ...

so a re sync with sensors now they have the same IDs.

Again in the cal ride didn't give me time to stop and turn around at 50%. No Calibration ride saved.

Here is the ride file that started at the end of the cal ride.
Does it look Ok?

Last night I set up both versions the V3 and V5 to "best" accuracy, which talks about the O&B ride. I checked the values and updated the Aero & Wind Scaling from a ride confirmed as good. Here are the 2 profiles Fat Bike V3.ibp Fat Bike v5.ibp I am a bit worried that the Wireless I...

Here is the v5 files

This is the V3 ride Power on the Garmin

I can see similar issues on both the V3 and V5 that I did today.

https://velocompforum.com/viewtopic.php ... ide#p31480

So I did a new cal ride. The cal ride didn't save but the from the end of the cal ride back to the car did save as a ride. This was on a V3. After that, I tested a friend's V5. He had been having issues with the calibration ride not saving and the ride restarting. Well the same happened for me as on...

Hello,
It has been a few months since my last ride. I charged the PowerPod and went for a ride. I was getting a Power reading on my Garmin.
I then connected my laptop to the PowerPod to download the ride data. The ride wasn't recorded.

I assume it is best to reset the device and do a new cal ride?

Hello
I can also confirm it works on an M3 chip. I have just installed and tested it.

I do have an issue, not with the software's installation or running. If I maximise the window everything turns upside down.

Here is the ride file. It all looks good even on the slow climb.

So have just climbed the hill. I have power numbers all of the way up - of course none on the downs. I will download the ride later.

The Garmin average Power the options are with or without 0.
Which is a the best choice?

Hello, So I created the VM on my Macbook so I could connect to the PowerPod. I upgraded the firmware and did a reset. I knew I should do a new calibration ride (new heart rate sensor, new wheels, removing the magnet speed sensor and my weight). So I did a calibration ride. I didn't know that I had t...

It is a strap and sensor (Garmin so they are one and the same)... so it is a cal ride... At the moment I can't run the software as my MacBook updated before I saw the warning... I hope that a friend will let me install the software on their laptop do help me do this...

Hello
Is it possible to swap HR straps without doing a new calibration ride?
Thanks

Now to put some real rides in the system. Let’s see how the hill climbing goes.

Thanks

Hello I just got and fitted the PowerPod to my bike. I have a Fat Bike. For this first ride, I was on a path by the river so no tracks or off-road. I remembered to turn off the suspension fork for this ride. Please can you check my cal and first ride? I think that everything is good to go. I have no...

Hello
Any advice on how far axle to the rim I should install this.
In the next week I should have my PowerPod to use this.
Many Thanks

How slow can I go with 2 magnets?
Thanks
Iain

any suggestion of which one to buy my quick search of Amazon germany didn't return any.

Hello, I am reading up on all the information while I wait for PowerPod to arrive. I am looking at my ride in Garmin connect. Most of my rides start with a hill climb of 160m in 3km. I am riding a FatBike so I can be slow on the hills. My minimum speed is about 5kmh (3.1 mph). Is there a way to adju...