AeroPod, PowerPod and Newton

I got readings like this, My cadence sensor was to close to the magnet which was causing a double count every revolution or so.

Chris

Thank you very much Fernando for your help! This is how I will go!

I will apologize in advance as this has probably been covered, but I have never been able to use a search engine with any success! I did try! I am putting on Aero bars! But will not be in them for the whole ride! And can not say how much of the ride will be in them or out of them! You have 2 profile...

John, I Thank you for your help!

I have to figure out what I did wrong then!

Again Thanks a bunch

Chris

Russ I do Thank you for your reply! I have looked in the setup on the Newton, and in Isaac, and I have not found the way to turn it off and get it to manual mode, I most likely am just missing this obvious step! Could I get this pointed out to me! It is easy to hide something from me just put it rig...

I have 2 Profiles on my Newton one for riding outside, and one for the trainer! They both use the same bike. What order does the Newton look for matching ID's, to determine which profile to use? My Newton picked a different profile yesterday than the one I had previously used! If it does not already...

If I do a Cal Wind on my Newton with the 5.0 firmware! Is this stored permanently on the Newton? Or is it lost if I do say a Hard Reset, or for any other reason?

I Thank you for your help and insight!

Chris

I have been using the Powerstroke option for a couple weeks now. When I down load every ride it asks me where me cadence sensor is. I have answered this question the same every time. I have gone into edit profiles - into the Powerstroke tab. It is set for Above the chainstay. Other than not using Po...

And we Thank You for all you do!!!

With my powerhouse, I need to scan for sensors before each ride! Is this normal, or am I doing something wrong?

Thanks in advance for your help!

Chris!

Wheat cleaner cloth is best to use on the window of the case? To get off all the finger prints!

Thanks for your time and help!

Chris

Great! I missed that in all my playing! Off I go!

Thanks a bunch! For all your great products!

In the winter with the snow it is a bit hard for new owners to get outside and do a Set-up ride! For those who have the trainer option! Would it be possible to let us use the plans on the trainer without doing the set-up ride? It really serves no purpose that I can see on the trainer! Then When we g...

I thank you for your reply!
For the workouts, I understand! But is there a to get answers for the questions?

Thanks in advance!
Chris

Hi Brand new to the Powerhouse! On the Powerhouse is there anything that indicates the additional battery is connected and helping? Other than waiting to see if you run out of power on your iphone/touch way to early! What would indicate it is time to swap batteries? When the iphone/touch is almost d...

Thanks a bunch! I am looking forward to this new adventure!

Hi I receive my powerhouse in a couple days, but am curious about the following! Thought I would ask! I understand that if you do not finish a ride on a given day, you have the option to save the ride and move on or discard the ride and do it again! What if you finish the ride, but did it very bad! ...

Very cool! Thanks a bunch! Y'all are the best!

Chris

Hi All

I there any possibility of getting and answer to my question above?

I do thank you for your help

Chris

I ride with a Newton now! I am going to have a Powerhouse soon! It is my understanding the the Fitness test for the Powerhouse is 12 minutes! I have also seen a time of 5 minutes! I have a couple questions! Can I do a 20 minute Fitness test for Powerhouse? So both the Newton and Powerhouse is on the...

Hi John
Above you said you could upgrade the Powerhouse, to a Dash + Power with a firmware key!
I can not find this option in your store on the internet!
Could you please tell me where to find this, and how to do this, and how much the upgrade will cost!

Thanks a bunch!

Chris

I am using the Garmin GSC 10 Speed/Cadence sensor! The Newton sees it fine! I do not have the GT firmware upgrade! I do not know about the Trek DuoTrap!

Nope! You can pick up the Ant + signal without the GT software! The GT firmware lets you send out the power data!

The only change I remember is: You now set the Altitude the normal way in setup/Alt this is now stored in memory! Then after that you can hit the Enviro key twice, where the altitude shows, hold the center button for 2 seconds and the Altitude you had set will be loaded! there were others but my mem...

I for one like this solution!

Velocomp put this into the firmware, as to many people were forgetting to take the unit out of trainer mode when they went back outside!

I put a piece of tape over it, and pull it off when I go outdoors!

You need to block the air intake opening. With air hitting the port it takes the Newton out of trainer mode!

Thanks a bunch!

With the Newton do you still have to do a Tilt Cal with in 20 minutes of doing the Cal ride?

Thanks for your help!

Chris